Few things feel worse than a bike that looks ready to go and will not fire. The Low Rider S is a bike you want to ride. It has the stance, the sound, and the attitude. So when it sits there dead, it stings a little extra.
The good news is that a Harley Davidson Low Rider S not starting is usually fixable with simple checks. In this guide, you will learn how to read the symptoms, test the easy things first, and know when to hand it to a shop. I will also share the mistakes I made so you can skip them.
What Harley Davidson Low Rider S Not Starting Usually Means
The first job with a Harley Davidson Low Rider S not starting is to work out what kind of problem you have. Does the engine crank or not? Does it start and then die? Each pattern points to a different part of the bike.
Listen when you press the starter. The sound is your best clue. Here is how I read it.
| What You Notice | Likely Direction |
|---|---|
| Silence, dash stays dark | Battery, main fuse, or connection |
| Rapid clicking | Weak battery or poor connection |
| One loud click | Starter relay or starter |
| Cranks fine, will not fire | Fuel, spark, or sensor issue |
| Starts, then stalls | Fuel supply, security, or sensor |
Treat this as a map, not a verdict. Confirm with a few tests before you buy any parts.
Why the model year matters
The Low Rider S name has been used on more than one generation of Harley. As far as I know, there was a Dyna version and a later Softail version. They differ in where the battery sits, how the electronics work, and what the manual says.
I am not certain about every detail for each year. So check your owner’s manual for your exact bike. It beats any general guide, including this one.
Easy Checks Before You Reach for Tools
Before you suspect anything big with a Harley Davidson Low Rider S not starting, rule out the small stuff. A surprising number of Low Rider S starting problems come down to a switch, a stand, or a fob. I now check these first, every single time.
| Area | What to Check |
|---|---|
| Engine run switch | Make sure it is in the run position |
| Kickstand | Raise it fully |
| Gear and clutch | Try neutral, and check your manual |
| Fob and security | Fob nearby, security light behaviour |
| Fuel | Level and a pump prime sound |
Each check takes seconds. If one fixes it, you saved yourself a lot of stress.
The run switch and the stand
The engine run switch sits on the right handlebar. It is easy to knock with a glove. If it is off, the bike will not start, however good the battery is.
The kickstand has a safety switch. If the stand is down while the bike is in gear, the engine may refuse to start or may cut out. Whether the clutch must be pulled in varies by model, so confirm in your manual.
I once spent ten minutes testing the battery. The stand was half down. Do not be me.
Fob and security light
Many newer Harleys use a fob based security system. The bike needs to sense the fob to start. A weak fob battery can cause strange behaviour.
Fob batteries are often a small coin cell, but check your manual for the type on your bike. Replacing one is cheap and quick. Also watch the security light on the dash, because it can behave differently when the system cannot see the fob.
Fuel and the pump prime
Never trust the fuel gauge alone. Check the tank level if you can do it safely, away from any flame or spark.
Then turn the ignition on and listen. Many fuel injected bikes make a short hum as the pump primes. If you hear nothing, note that down. It points toward a fuse, relay, or the pump itself.
Battery First: Why Cruisers Struggle
If I had to bet on the cause of a Harley Davidson Low Rider S not starting, I would bet on the battery. Cruisers often sit for days. Many get ridden in short trips, which never fully recharge the battery.
A battery can look fine and still fail under load. A simple test tells you the truth. A basic multimeter costs little and saves a lot of guessing.
Short rides and slow drains
Short rides are tough on batteries. Starting the engine uses a lot of power. A ten minute ride may not give that power back.
I noticed this myself. My bike started fine for weeks, then failed after a stretch of quick errands. A longer ride or a tender fixed it.
How to test the battery
Set your meter to DC volts and touch the probes to the terminals. Read it with the bike off and rested. Then watch it while cranking. The numbers below are approximate for a typical lead acid or AGM battery.
| Test | Good Sign | Warning Sign |
|---|---|---|
| Resting voltage | About 12.6V or higher | Near 12.0V or lower |
| While cranking | Stays reasonably steady | Drops very low |
| Running, revved a little | Roughly 13.5V to 14.5V | Stays near resting level |
Check your manual for exact figures. If the numbers look poor, charge the battery fully and test again.
Finding the battery and checking the terminals
The battery location depends on the year and model. On some bikes you need to remove the seat or a cover to reach it. Your manual shows how.
Check that the terminals are tight and clean. Loose or crusty terminals mimic a dead battery. Disconnect the negative terminal first when you work near the battery, and reconnect it last.
Harley Davidson Low Rider S Not Starting but Cranking
A Harley Davidson Low Rider S not starting while it cranks is the more puzzling case. The engine spins, so the battery and starter are doing their jobs. But nothing fires. That points to fuel, spark, or a sensor.
Work through them in that order. Avoid guessing.
Fuel delivery and stale petrol
A fuel injected bike needs a working pump, good pressure, and fresh fuel. Fuel left in the tank for months can go stale. Ethanol blends can make it worse.
If the bike sat unused, stale petrol is a prime suspect. Draining it and adding fresh fuel often helps. I avoid starter fluid on fuel injected bikes, since it can cause damage and a fire risk.
Spark plugs and ignition parts
Worn or fouled spark plugs can cause hard starting. They are cheap and often easy to inspect. Use the service manual for the right plug and gap on your year.
Treat ignition coils with care. They carry high voltage. If you do not feel confident testing them, let a professional do it.
Sensors and fault codes
Modern Harleys depend on sensors, such as the crankshaft position sensor. If a key sensor fails, the engine may crank without starting.
A dealer or a good independent shop can read fault codes with the right tool. That beats swapping parts at random, which I have done and regret.
When a Low Rider S Starts Then Stalls
Some bikes fire up and die within seconds. That is a different puzzle from a bike that will not fire at all. It tells you the basics work, at least for a moment.
Dying right after it starts
If the engine starts and cuts out quickly, think about fuel supply, the security system, and sensors. Weak fuel pressure can let the engine fire and then starve. A security issue can also shut the engine down.
I would also check the battery and charging. A battery near the edge can start the bike and then let the electronics drop out.
Hot versus cold behaviour
Pay attention to when it happens. Does it struggle only when cold? Only when hot? Only after a fuel stop? Patterns help a mechanic a lot.
I keep short notes on my phone. Lines like “fine cold, hard after a ten minute stop” save diagnostic time.
If the pattern is clear and the fix is not, bring the notes to a shop. It can save you money.
Aftermarket Mods and Hard Starting
Many Low Rider S bikes get custom parts, and a modified Harley Davidson Low Rider S not starting needs a different approach. Exhausts, intakes, and tuners are popular. They can change how the bike behaves. Sometimes that includes starting.
If a modified bike is not starting, ask what changed recently. A new part or a new tune can be the cause. I would never rule it out.
| Modification | Possible Starting Effect |
|---|---|
| Aftermarket exhaust | Fuel mixture may need retuning |
| Intake change | Same, needs correct tune |
| Tuner or custom map | Wrong settings can cause hard starts |
| Added lights or gadgets | Extra drain or wiring faults |
These are possibilities, not certainties. A proper tune by a skilled shop avoids most of them.
Exhausts, intakes, and tunes
Changing airflow without matching the fuel map can cause rough running and hard starting. Many riders get a tune after fitting an exhaust.
If your trouble began right after a mod, talk to the shop that fitted it. They may know a fix. A reset to the stock map can also help you narrow the cause.
Wiring and accessories
Extra lights, chargers, and gadgets draw power. A poorly wired accessory can drain the battery even with the bike off. Use quality parts and proper fuses.
If the battery keeps going flat for no clear reason, ask a shop to test for a parasitic drain. That test finds power leaking while the bike is off.
Warning Signs Before a Harley Davidson Low Rider S Not Starting
A bike rarely fails without a hint. Looking back, I missed small signs that showed up days or weeks before the big failure. Spotting them early can save a ruined ride.
Slow or lazy cranking
If the engine turns over more slowly than it used to, take it as a warning. It often points to a tired battery or a weak connection. Cold mornings make it easier to notice.
I ignored this once for two weeks. Then the bike refused to fire at the worst moment, far from home. A quick charge test would have caught it.
A flickering dash or dim lights
Flickers, resets, or dim lights when you press the starter suggest a power problem. The cause can be a low battery, a loose terminal, or a poor ground connection.
Strange behaviour from the dash or the lights is often the first clue that voltage is dropping.
Hard starting that comes and goes
Intermittent trouble is the hardest to track. If the bike starts fine cold but struggles hot, or the other way around, write down when it happens.
Notes like “only after rain” or “only after a fuel stop” can point straight at the cause.
Cold Weather, Storage, and a Low Rider S That Will Not Start
Many starting problems appear after winter or a long break. Cold thickens oil and cuts battery power. Storage lets fuel go stale and lets batteries drain.
If your Harley Davidson Low Rider S not starting problem shows up after storage, think battery and fuel first. Those two cause most of the trouble I have seen.
Before the first ride of the season, I charge the battery fully and check the terminals. I also look at the fuel. If it smells sour or looks dark, I replace it with fresh fuel.
Cold weather tests a battery harder. A battery that works in summer can fail on a frosty morning. If your bike struggles in the cold, test the battery before you blame anything else.
Do not crank the engine again and again. Short bursts with rests in between are kinder to the starter and the battery. Check your manual for the approach it recommends.
If the bike still will not start after a charge and fresh fuel, it is time for deeper checks. Do not push through with repeated cranking. That only makes things worse.
Why a Low Rider S Can Be Easier to Diagnose
A Low Rider S usually has fewer electronic extras than a big touring bike. There is less audio, less lighting, and less wiring to hunt through. That often makes problems easier to find.
In my experience, that means a simple order of checks gets you far. Battery, switches, fuel, and spark cover most cases. You rarely need to dig deep right away.
The catch is customisation. Many owners change parts, add accessories, or fit tuners. That can add hidden variables. If your bike is modified, think about what changed.
Exposed parts also face more weather. Connections can corrode over time, especially if the bike lives outside. A quick look at the terminals and visible wiring is worth the effort.
I am describing general patterns here, not rules. Every bike has its own history. Your manual and a qualified mechanic have the final say.
A Simple Order for Troubleshooting
When the bike will not start, a clear order keeps you calm. This is the sequence I follow now. It goes from the cheapest check to the most involved.
- Check the run switch, kickstand, and gear position
- Make sure the key fob is present and working
- Look at the dash and listen for the pump prime
- Test battery voltage and check terminals
- Check the main fuse and other fuses
- Think about fuel age and spark plugs
- Get fault codes read if it cranks but will not start
Take your time with each step. Do not skip ahead. Most problems show up in the first four.
Write down what you find. If you end up at a shop, those notes save diagnostic time and may save money too.
Jump Starts, Chargers, and Safe Fixes
A low battery often needs only a good charge. A smart charger or tender is the safest way, since it charges slowly and protects the battery.
If you must jump start, check your manual first. Connect the leads in the correct order and never reverse them. Wrong connections can harm the electronics.
Whatever you do, keep sparks and flames away from fuel. Work in an open, dry space.
When to Fix It Yourself and When to Call a Shop
Some fixes are easy. Others get expensive when you guess. Here is how I split them.
| Problem | DIY or Shop |
|---|---|
| Loose or dirty terminals | DIY |
| Low battery needing a charge | DIY with a smart charger |
| Fob battery | DIY |
| Blown fuse | DIY, but find the cause |
| Fuel pump or sensor fault | Usually a shop |
| Starter or charging faults | Usually a shop |
These are general suggestions. Your skill, tools, and warranty all matter. When unsure, ask a professional.
Low Rider S Starting Myths
Advice about a Harley Davidson Low Rider S not starting spreads fast, and some of it is wrong. I believed a few of these myself. Here is what I learned.
| Myth | Reality |
|---|---|
| A new battery fixes everything | A bad cable or relay can fake a dead battery |
| If it cranks, it is fine | Fuel, spark, or sensors can still fail |
| Starter fluid is a safe test | It can damage fuel injected bikes |
| A full tank means fuel is fine | Old fuel or a weak pump can still cause trouble |
None of these myths is always wrong. They are just incomplete. Test before you spend.
Mistakes to Avoid When a Low Rider S Will Not Start
I made most of these mistakes myself while dealing with a Harley Davidson Low Rider S not starting. Each one cost time, money, or both. Learn from them and save yourself the grief.
Replacing parts by guesswork
I once bought a part because a forum thread said so. It did nothing. The real cause was a loose connection. Test first, then replace.
Cranking again and again
Repeated cranking drains the battery and stresses the starter. Crank in short bursts, then stop and think. Check your manual for the recommended approach.
Ignoring early warning signs
A slow crank or a flickering dash is a hint. I ignored both once. Then the bike failed far from home. Act on early signs and test the battery.
Habits That Prevent Starting Problems
The best fix for a Harley Davidson Low Rider S not starting problem is not needing one. A few habits keep a Low Rider S ready to ride. None take much time.
Keep the battery charged
Use a smart tender if the bike sits for more than a week or two. It keeps the charge steady without overcharging. Take a longer ride now and then, too.
Use good fuel and store it well
For long storage, use fresh fuel and a quality stabiliser. Follow the product directions. That helps avoid the stale fuel trouble that causes hard starting.
Check the small things
Look at terminals, fuses, and wiring now and then. Catching a loose connection early is much easier than fixing a roadside breakdown. Keep your manual handy for model-specific steps.
Questions People Ask About a Low Rider S Not Starting
These are the questions I hear most. I kept each answer short so you can scan quickly.
Why is my Harley Low Rider S not starting?
The usual causes are a weak battery, a loose connection, a switch in the wrong position, or a fuel issue. Listen to the sound when you press the starter. It points you to the right area.
Why does my Low Rider S click but not start?
Rapid clicking usually means low power or a poor connection. A single click can point to the starter relay or starter. Test the battery and terminals first.
Why does it crank but not start?
If it cranks normally, the battery is probably fine. Look at fuel, spark, and sensors next. Old fuel is a common cause after storage.
Can mods stop a Harley from starting?
Yes, they can. An exhaust, intake, tuner, or accessory can change how the bike runs or drain the battery. Ask what changed before the trouble began.
How do I know the battery is dead?
Use a multimeter. A fully charged battery rests around 12.6V or higher. Much lower readings suggest it needs a charge or a replacement.
Final Thoughts
The biggest lesson I learned is to stay calm and test in order. A Harley Davidson Low Rider S not starting is rarely a disaster. Most of the time it comes down to the battery, a connection, a switch, old fuel, or a recent change.
My honest advice is to check the easy things first, learn what the sounds mean, and keep a tender on the battery. Details vary by model year, so confirm anything important in your owner’s manual or with a qualified mechanic. If the problem goes beyond a simple check, a good shop is worth the money.
Ehatasamul Alom is a dedicated road hybrid bikes expert. With over 15 years of experience, he helps people find the perfect ride. He began his journey as a bike mechanic. He learned the ins and outs of every bike.
Ehatasamul Alom holds a Master's degree in Mechanical Engineering from a Brown University (Providence US 02912), where he specialized in material science and bicycle kinematics. His master's thesis focused on optimizing frame geometry for road hybrid bikes to improve rider comfort and efficiency.
Ehatasamul has an extensive professional background. He spent 10 years (2010-2020) as a Senior Bike Designer at "Urban Cycles," a leading bicycle manufacturer. In this role, he led the development of several award-winning road hybrid bikes, which are known for their durability and performance. He later served (2020-2024) as the Head of Product Development at "Gear Up," a company specializing in high-end cycling components. There, he developed innovative parts and accessories specifically for road hybrid bikes.
Over the years, Ehatasamul has become an authority on Roadhybridbikes. He understands their design and function. His work focuses on making bikes easy to use. Ehatasamul believes everyone should enjoy cycling. He writes guides that are simple to read. His passion for road hybrid bikes is clear. His goal is to share his knowledge with everyone. He wants to see more people on two wheels. His advice is always practical and easy to follow.
