Harley Davidson Breakout 117 Not Starting? What to Check

You swing a leg over the Breakout, press the button, and get nothing. No roar, no crank, just an awkward silence. A Harley Davidson Breakout 117 not starting is a rough way to start a weekend.

I have chased a few no-start problems on big cruisers. Most of them ended with a simple fix. In this guide, I sort the problem into four clear scenarios. I lean on Harley-Davidson’s own starting advice, and I paraphrase it in plain words. I am not a certified Harley tech, so check your owner’s manual for your exact model year.

Harley Davidson Breakout 117 Not Starting? Match Your Scenario

Random guessing wastes time. A simple sort works better. Look at the dash, listen, and then pick the scenario that fits.

Harley’s own guide uses a similar idea. I have added the Breakout angle.

ScenarioFirst Move
Dash on, starter silentCheck switches and the fob
No lights at allCheck terminals, fuse, and battery
Clicks and weak lightsCharge the battery, drop the extras
Cranks but never firesCheck fuel, spark, and air

Why sorting helps

Each scenario points to a different system. Power problems look different from fuel problems. Naming yours first saves a lot of time.

What a Breakout 117 is

The Breakout is a Softail cruiser. Dealer listings and Harley’s 2025 lineup list it with a Milwaukee-Eight 117 engine. That is a big V-twin, and it needs solid power to turn over.

As an Amazon Associate I earn from qualifying purchases.

Scenario One: Lights On, Starter Silent

A Harley Davidson Breakout 117 not starting with a live dash is common. You press start, and the starter stays quiet. That means the bike has power, but something is holding back the start signal.

This scenario is often the cheapest to fix. Go slowly through these checks.

Is the OFF/RUN switch on RUN?

Harley’s guide points out that the switch may have been bumped to OFF without you noticing. Even riders who never touch it can knock it by accident. The dash can still light up, which fools many people.

Flip it to RUN and try again. I know it sounds silly. It still catches me now and then.

Neutral, clutch, and the sticky switch

Many Harleys need neutral, the clutch lever pulled in, or both. A small switch at the lever sends that signal. Harley says it can stick sometimes.

A quick fix is to squeeze and release the clutch lever a few times. Then try again. If you are in neutral, some bikes will start without the clutch pulled.

The side stand switch

Some bikes use a side stand switch. The stand must be up for the bike to start. The switch sits low, so dirt can make it stick.

Harley suggests cleaning it with soapy water and a toothbrush or rag. Do it with the bike off and the fob away. It is an easy, cheap job.

Keyless Ignition and the Fob on a Breakout 117

Most recent Softails use keyless ignition with a security fob. Harley’s 2018 Softail announcement lists keyless ignition and security as standard on that lineup. The system blocks the starter if it cannot find the fob.

This is a top suspect when the dash is on and the starter is silent.

SignWhat It Often Means
Dash on, no crankFob not detected
Security light flashingSystem still armed
Works with PIN, not fobWeak fob battery or fob fault
Starts after fob is closerRange issue

How close does the fob need to be?

Harley’s service pages give the disarm range as about five feet from the centre of the bike. That is a small bubble. A fob in a pannier or a far pocket can miss it.

With the fob out of range, the starter and ignition stay disabled. That is by design.

Replace the fob battery

Many fobs use a CR2032 coin cell. Check yours to be sure. A weak cell may still light the fob but fail to reach the bike.

I swap mine yearly. It costs very little. It removes a common no-start cause.

Use the PIN backup

Harley says the PIN can disarm the security system. The exact steps depend on the model, so use your manual. Do not follow random videos for this.

If you never set a PIN, do it now. Keep it somewhere safe.

Scenario Two: No Lights at All

If your Harley Davidson Breakout 117 not starting comes with a dark dash, no power reaches the bike’s wiring. The cause is usually simple. Do not rush to the starter.

Harley’s guide gives a sensible order. I follow it.

Check the battery cables

Look at both terminals. They should be tight and free of crust. A loose clamp can act like a dead battery.

I once spent a long time on a bike that only needed a snug cable. It still makes me laugh.

Look for a blown main fuse

Many bikes have a main fuse between the battery and the wiring. If it blows, nothing gets power. Harley says that a fuse that blows again suggests a short, and that needs a shop.

Fuse locations vary by model, so check your manual. Do not swap in a bigger fuse. That is unsafe.

Test the battery voltage

Try a multimeter for a quick view. A healthy 12-volt battery often reads about 12.6 volts at rest. These are general numbers, so check your battery maker’s advice.

A voltage check is not a full load test. A shop can do that if you are unsure.

Scenario Three: Clicks and Weak Power

A click or a rapid clicking means some power gets through, but not enough. The starter needs far more power than the lights do. So the dash can look fine while the bike cannot crank.

Harley’s guide says this often comes from leaving something on. That includes parking lights or powered accessories.

Power HogWhy It Matters
Parking lights left onDrain the battery overnight
GPS or audio left poweredSlow draw while parked
Heated gearCan outpace the charging system
Phone chargersSmall draw that adds up
Aftermarket alarmsConstant small draw

Charge it first

If you left something on, turn it off. Then charge the battery with a proper charger. Harley points riders to its battery charging guide.

Use a smart charger made for motorcycle batteries. Charge in a ventilated spot, away from sparks.

Think about your accessories

If you ride with many add-ons, you may draw more power than the charging system makes. The battery slowly sinks. Then one day, it will not start.

I learned to unplug extras when I park. That one habit helped a lot.

Check the charging system

Harley says a healthy charging system should show about 14.0 to 14.7 volts at the battery with the engine running above idle. About 12 volts means no charge is going in. A technician should check that.

Do this test only if you can start the bike. Otherwise, ask a shop.

Scenario Four: It Cranks but Will Not Fire

Here the starter works. In this kind of Harley Davidson Breakout 117 not starting case, power and safety are probably fine. Now you look at fuel, spark, and air.

This is where the work gets harder. Be honest about your skill level.

Listen for the fuel pump

Harley notes that you should hear an electric fuel pump hum when you switch on. If you hear nothing, the pump may have failed, a fuse may have blown, or a wire may be loose. A pump repair is a job for a pro.

Old fuel is a real problem

Harley warns that modern fuel, especially with ethanol, can start to break down in about 30 days. If the bike sits for more than a few weeks, use a fuel stabiliser. Then ride a short way so the treated fuel reaches the whole system.

That is a lesson I took seriously. It is easier than draining a tank.

Spark plugs and leads

Fouled plugs or loose leads can stop a bike from firing. Harley suggests checking that lead caps are tight. If the leads look dry or cracked, replace them.

Blocked exhaust

An engine that cannot push air out cannot run. Harley mentions that mice can nest in the exhaust during long storage. That sounds odd, but it happens.

If you suspect pests, a shop may need to remove the muffler. Do not force the engine to crank.

Do not crank forever

Long cranking strains the starter and drains the battery. Use short bursts. Rest between tries.

If you smell strong fuel, stop. Fuel is a fire risk, so keep sparks away.

Why a Big Cruiser Can Feel Fussy to Start

The Breakout 117 carries a large V-twin. A big engine asks a lot of the starter and the battery. That is why a tired battery shows up fast on a bike like this.

I do not see this as a flaw. It is just how big engines work. Keep the power healthy and the bike rewards you.

The battery is the first link

A cruiser sits for days between rides. The security system and clocks draw a little power. Over weeks, that adds up.

If the bike cranks slowly, treat it as a warning. Test the battery before it leaves you stuck.

More electronics, more checks

A modern cruiser has a fob, a security system, and a digital display. They need clean power to work well. Low voltage can cause odd behaviour.

When the dash acts strange, I suspect the battery first. That rule has saved me time.

Do not compare it with an old Harley

Older bikes used a key and simple switches. A Breakout uses a fob and a security system. A fix that worked on a vintage bike may not apply here.

Harley Davidson Breakout 117 Not Starting After Winter Storage

Many no-starts happen after a long layup. Fuel ages, batteries fade, and pests move in. Spring is the busiest time for these calls.

A short routine in autumn helps.

Before you store it

Add a fuel stabiliser and ride a short way. Connect a battery tender. Cover the bike and block pest access.

On the first ride of spring

Check the tyres and the terminals. Look under the bike and around the exhaust for nests. Then start the bike and let it run before you set off.

Be patient with old fuel

If the bike will not fire after a long layup, think fuel first. A shop may need to drain and refill the tank. It costs less than damage from forcing it.

Reading the Sounds and the Dash

Your bike speaks in clicks, hums, and lights. Most riders ignore them. I now treat them like a short report.

Note what you hear before you try again.

Clicks tell a story

One click and rapid clicks both point to low power. The starter asks for more than the battery can give. Charge the battery first.

The pump hum

A short hum at switch-on is the pump building pressure. If you hear it, fuel delivery has at least started. If you do not, make a note for the shop.

Display messages

A message about the fob tells you the bike cannot find it. A dim or flickering display suggests low voltage. Take a photo of anything odd. It helps a mechanic later.

Harley Davidson Breakout 117 Not Starting in Cold Weather

Cold mornings expose weak parts. A cold battery gives less power. Oil thickens, so the starter works harder.

I notice this most in the first cold week of the year.

Why mornings are harder

A battery that works in summer may fail at dawn. By lunch, it may start fine. That pattern is a warning sign.

Test the battery when you see it. Do not wait for a full failure.

Short winter rides

Short trips leave the battery undercharged. The charge slips week by week. Take a longer ride when you can, and use a tender between rides.

My Step-by-Step Order for a Breakout 117 That Will Not Start

A fixed order keeps me calm. It also stops me from buying parts I do not need.

Work down the list. Stop when the bike starts.

Steps one to three: switches

First, set OFF/RUN to RUN. Second, use neutral and squeeze the clutch a few times. Third, check the side stand switch.

Steps four and five: fob and power

Fourth, bring the fob close and replace its battery. Fifth, check the terminals and test the battery. Charge it if it reads low.

Steps six and seven: fuel and help

Sixth, listen for the pump and think about old fuel. Seventh, call a shop. That is a smart move, not a failure.

Common Mistakes With a Breakout 117 That Will Not Start

Stress makes us hurry. I have made several of these slips. Here is a better way.

MistakeBetter Approach
Cranking nonstopUse short bursts with rests
Skipping the OFF/RUN switchCheck it first
Ignoring the fobReplace its battery yearly
Buying a starter earlyTest the battery and switches first
Using a bigger fuseUse the correct rating only

Jump starts and electronics

A careless jump start can harm sensitive electronics. Check your manual first. Many riders choose to charge the battery instead.

Buying parts too soon

It is tempting to order a starter right away. Test first. A loose cable costs nothing to fix.

Safety First Before You Touch Anything

A no-start tempts you to rush. Please do not. Fuel, batteries, and hot parts can hurt you.

These rules keep me out of trouble.

Work in a safe space

Park on level ground with the engine off. Keep the area ventilated. Stay away from sparks, flames, and smoking.

Protect yourself

Wear gloves and eye protection near the battery. Take off rings and watches. A metal ring across a battery post can burn you fast.

If you feel unsure, stop. Ask a pro. No ride is worth an injury.

Simple Tools Worth Keeping in the Garage

You do not need a full workshop. A few cheap items solve most no-start days. I keep them in one box.

The basics

A digital multimeter shows battery voltage. A smart charger or tender keeps the battery topped up. A spare CR2032 coin cell covers the fob.

Small extras

A toothbrush and soapy water clean the side stand switch, as Harley suggests. A torch helps you see wiring. Keep your owner’s manual in the garage, with the PIN page marked.

DIY or Shop? Know Where to Stop

Some jobs are easy. Others need tools and training. Being honest about your skill keeps you safe.

Here is how I split them.

TaskDIY or Shop
Check OFF/RUN and clutch switchDIY
Clean the side stand switchDIY
Replace the fob batteryDIY
Charge and test the batteryDIY, with care
Test the charging systemShop, unless skilled
Replace fuel pump or starterShop
Clear a blocked exhaustShop

Help the mechanic help you

Bring notes. Say what the bike did, what you tried, and how long it sat. Good notes cut labour time.

Roadside help

Harley says Harley Owners Group members get roadside assistance. Insurance may offer it too. Check what you have before you need it.

When a Breakout 117 Keeps Failing the Same Way

A bike that fails once may have had a bad day. A bike that fails the same way twice has a story to tell. Treat repeat failures seriously.

Keep short notes after each no-start. Write the date, the weather, and what you tried. A pattern often shows up within a few entries.

Share the pattern with your dealer

Tell the shop how long the bike sat and what the dash showed. Mention any accessories you added. That detail can point them to the right test fast.

Ask about software and service history

Ask whether any updates or recalls apply to your model. Harley lists recall information on its website. Checking costs nothing and can save you a repeat visit.

Habits That Prevent a No-Start

Prevention is cheaper than a tow. A few habits keep a Breakout ready to ride. I built these over time.

Keep power healthy

Use a tender when the bike sits. Turn off accessories when you park. Check the terminals now and then.

Treat the fob like a key part

Replace the fob battery yearly. Keep a spare fob safe at home. Set your PIN and store it securely.

Respect the fuel

Use stabiliser before long layups. Ride the bike regularly. Fresh fuel makes starting easier.

Myths About Harley No-Start Problems

Riders trade many half-truths about a Harley Davidson Breakout 117 not starting. Some sound sure and lead you astray. Here are a few I have heard.

MythReality
Lights on means the battery is fineThe starter needs much more power
It must be the starterMany causes come first
Fuel never goes badIt can break down in weeks
The fob never failsA weak fob battery is common
New parts always fix itTesting comes first

Quick Answers for a Harley Davidson Breakout 117 Not Starting

Here are the questions riders ask most. I keep each answer short.

Why is my Harley Davidson Breakout 117 not starting but the dash is on?

Check the OFF/RUN switch, the fob, neutral and clutch, and the side stand. The battery may also be weak. Lights need far less power than the starter.

Why does it click but not crank?

Clicks often mean a weak battery. Charge it and check the terminals. Accessories left on can drain it.

Can a dead fob battery stop a Breakout?

Yes. If the bike cannot detect the fob, the starter stays disabled. Replace the fob battery and keep the fob close.

Why does it crank but not fire?

Look at fuel, spark, and air. Old fuel after storage is common. A shop can test the pump and read fault codes.

How do I test the charging system?

With the bike running above idle, a healthy system often reads about 14.0 to 14.7 volts, according to Harley. If you only see about 12 volts, see a technician.

Final Thoughts

A Harley Davidson Breakout 117 not starting feels worse than it usually is. Many cases of a Harley Davidson Breakout 117 not starting come down to a switch, a fob battery, or a weak main battery. Sort your symptom into a scenario, run the free checks, and test the battery before you buy parts.

Expect to call a shop at some point. That is fine. Keep a tender on the bike, replace the fob battery every year, and use fuel stabiliser before long storage. A little care means more rides and fewer tows.

Co-Founder, Owner, and CEO at  – admin@roadhybridbike.com – Web

Ehatasamul Alom is a dedicated road hybrid bikes expert. With over 15 years of experience, he helps people find the perfect ride. He began his journey as a bike mechanic. He learned the ins and outs of every bike.

Ehatasamul Alom holds a Master's degree in Mechanical Engineering from a Brown University (Providence US 02912), where he specialized in material science and bicycle kinematics. His master's thesis focused on optimizing frame geometry for road hybrid bikes to improve rider comfort and efficiency.

Ehatasamul has an extensive professional background. He spent 10 years (2010-2020) as a Senior Bike Designer at "Urban Cycles," a leading bicycle manufacturer. In this role, he led the development of several award-winning road hybrid bikes, which are known for their durability and performance. He later served (2020-2024) as the Head of Product Development at "Gear Up," a company specializing in high-end cycling components. There, he developed innovative parts and accessories specifically for road hybrid bikes.

Over the years, Ehatasamul has become an authority on Roadhybridbikes. He understands their design and function. His work focuses on making bikes easy to use. Ehatasamul believes everyone should enjoy cycling. He writes guides that are simple to read. His passion for road hybrid bikes is clear. His goal is to share his knowledge with everyone. He wants to see more people on two wheels. His advice is always practical and easy to follow.