When your electric self-start button gives zero response and twenty hard kicks on the lever still leave the engine silent, panic sets in fast. Dealing with a Hero bike not starting with kick and self is uniquely frustrating because the kickstarter is supposed to be your foolproof backup when the electric starter fails.
I have rescued plenty of Hero commuters from Splendor Plus and HF Deluxe to Passion Pro, Glamour, and Xtreme models—when both starting systems quit at the exact same time. Below, I am sharing the real reasons both systems fail together, the rookie mistakes I made early on, and the exact five-minute checks that get you riding again without paying for an unnecessary tow.
Why a Hero Bike Not Starting With Kick and Self Happens Simultaneously
When both the electric starter and the kick lever fail together, the problem is almost never your starter motor or kick gear. Instead, something shared by the entire engine like ignition spark, fuel delivery, safety cut-off switches, or cylinder compression has stopped working.
The Crucial Difference Between Carbureted and BS6 Hero Models
Before opening a single side panel, check whether your Hero motorcycle is an older carbureted model (BS3/BS4) or a newer BS6/OBD2 Programmed Fuel Injection (PGM-FI) bike.
On an older carbureted Hero bike, the kickstarter generates its own spark directly from the engine’s AC magneto coil. Even with a completely dead battery, it will start in two kicks if fuel and spark are present. On a modern BS6 Hero bike, however, the Engine Control Unit (ECU) and electric fuel pump both need battery voltage to run meaning a flat battery or tripped safety sensor disables both the self-start and the kickstarter at once.
The First Five Seconds Before Touching Any Tools
Turn the ignition key to ON, flip the red engine kill switch (if equipped) to RUN, and pay close attention to your dashboard and fuel tank.
Look at the speedometer console to see if the neutral light illuminates and whether the amber side-stand warning light stays glowing. On BS6 models, lean down near the fuel tank and listen for a two-second buzzing sound from the fuel pump. Those five seconds narrow down your fault immediately.
| Key-On Observation | Shared System Affected | First Quick Check |
| Amber side-stand icon glows on dash | Side-stand ignition cut-off circuit | Fold side stand up fully and clean pivot sensor |
| Console completely blank, zero response | Main fuse or completely flat battery | Inspect 10A/15A fuses inside side panel |
| Console lights up, no fuel pump buzz | Fuel pump fuse, kill switch, or pump motor | Cycle kill switch and check fuel pump fuse |
| Pump buzzes, engine spins, never fires | Spark plug short, fuel blockage, or compression | Check spark plug cap and fuel delivery |
Side-Stand Cut-Off, Kill Switch, and i3S Interlock Traps
More than half of the modern Hero bikes I have helped restart after both kick and self-start failed had zero mechanical damage. They were simply locked out by Hero’s electronic safety sensors.
The Side-Stand Sensor Mud and Chain Lube Trap
On BS6 and XTEC Hero models, the side-stand engine cut-off switch disables ignition spark and fuel injection whenever the stand is lowered blocking both self-start and kickstarting completely.
Flung chain lube, wet mud, and road dust pack tightly around the side-stand pivot sensor behind the left footpeg. Even after you kick the stand all the way up, thick grime can hold the magnetic switch open. Snapping the stand up and down firmly six or seven times or washing the pivot bracket with clean water—clears this lockout in seconds.
How a Dirty Kill Switch or Bank-Angle Sensor Kills Both Starters
On models equipped with a red handlebar engine kill switch or a frame-mounted bank-angle (tip-over) sensor, an open circuit cuts power to the ignition coil and fuel injector simultaneously.
I once spent twenty minutes kicking a friend’s Passion Pro after it tipped gently onto soft grass, only to remember the bank-angle sensor had tripped. Turning the ignition key completely OFF for ten seconds and switching it back ON reset the ECU, and the bike fired up on the very first touch.
| Safety Switch | Normal Function | Why Both Kick and Self Fail |
| Side-Stand Sensor (BS6) | Disables ignition when stand is down | Mud or bent bracket keeps circuit permanently open |
| Handlebar Kill Switch | Cuts ECU and ignition coil power | Green copper oxidation inside switch blocks current |
| Bank-Angle Sensor | Shuts off fuel and spark after a drop | Stays locked until key is turned OFF for 10 seconds |
Spark Plug Fouling, Water Wash Shorts, and Loose Caps
If your Hero engine spins freely with the self-start and turns over with normal resistance on the kick lever—yet refuses to cough or fire—your spark plug is the prime suspect.
Monsoon Puddle Splash and Pressure-Wash Shorts
Most Hero commuters use a horizontal or forward-inclined single-cylinder engine positioned directly behind the front tire’s spray zone.
Riding through deep rainwater puddles or blasting the engine with a high-pressure foam washer forces water inside the rubber spark plug suppressor cap. Once moisture coats the ceramic insulator, high-voltage spark jumps straight to the cylinder head metal instead of firing inside the combustion chamber. Pulling the rubber plug cap off, drying it thoroughly with a clean cloth, and pushing it back until it clicks solves this wet-weather headache fast.
Black Carbon Fouling From Choke Errors and Short Starts
On carbureted Hero bikes, leaving the choke lever pulled up after the engine warms up floods the cylinder with rich petrol and coats the spark plug electrode in black soot.
On BS6 fuel-injected bikes, starting the engine for fifteen seconds just to move the bike out of a parking spot and shutting it off immediately causes the exact same wet carbon fouling. Removing the spark plug with the under-seat box spanner, cleaning off the black soot, and testing for a crisp blue spark against the cylinder head fin confirms whether the plug is healthy.
| Spark Plug Clue | Real-World Cause | Practical Fix |
| Wet, black, fuel-soaked electrode | Choke left ON or brief cold-start shutoffs | Wipe plug dry, brush off soot, and ventilate cylinder |
| Water droplets inside rubber plug boot | Deep puddle splash or pressure washing | Dry boot completely and push down until it clicks |
| Weak yellow spark or total zero spark | Worn spark plug or failing ignition coil | Install fresh spark plug and check coil spade wires |
Fuel Starvation: Blocked Carburetors vs. Silent BS6 Pumps
An engine needs three things to run: spark, fuel, and compression. When you confirm bright blue spark at the plug, a Hero bike not starting with kick and self means petrol is not reaching the cylinder.
Draining Water and Sediment From Carbureted Hero Bikes
Rainwater sneaking past an aging fuel tank cap rubber gasket sinks straight to the bottom of the tank and enters the carburetor float bowl the moment you switch to reserve.
Here is a simple roadside fix that works on nearly every carbureted Hero commuter: turn the fuel tap OFF, hold a rag beneath the carburetor, and loosen the brass drain screw at the bottom of the float bowl with a flathead screwdriver. Draining two spoonfuls of dirty fuel and water—then tightening the screw and turning the fuel tap back ON—clears blocked pilot jets without dismantling anything.
Why Cruising on Reserve Destroys BS6 Fuel Pumps
On fuel-injected BS6 Hero models, the electric fuel pump sits submerged inside the petrol tank and uses surrounding fuel to stay cool and lubricated.
Habitually riding around with the fuel gauge blinking on empty overheats the pump motor and pulls settled tank sediment into the intake strainer. If you turn the key on a BS6 Hero bike and hear dead silence instead of a two-second pump hum, check the 10A/15A fuses inside the side box before inspecting the wiring coupler beneath the tank.
| Fuel Delivery Fault | Carbureted Hero Fix | BS6 Fuel-Injected Hero Fix |
| Water or rust in petrol | Drain carburetor float bowl screw | Drain tank and clean fuel pump strainer |
| Vapor lock after refueling | Check tank cap vent hole for blockage | Pop fuel cap open 10 seconds to release vacuum |
| Zero fuel flow to engine | Inspect fuel petcock and inline filter | Check fuel pump fuse and 2-second key-on hum |
Dead Batteries, Blown Main Fuses, and Stator Coil Failures
Many riders assume a dead battery only stops the self-start button, yet electrical failures can easily disable both starting methods depending on your bike’s design.
Why a Flat Battery Stops a BS6 Hero Even When Kicking
I made the mistake of kicking a friend’s BS6 HF Deluxe twenty times in a row before realizing the 12V battery had dropped down to 7.8 volts.
Because a BS6 Hero bike relies on battery voltage to power the ECU and run the electric fuel pump before firing, kicking with a completely flat battery produces zero fuel spray. Even if your headlight bulb glows dimly, voltage below 9.5 volts prevents the fuel pump from building rail pressure. Connecting jumper cables from another healthy 12V bike battery starts it immediately.
Blown Main Fuses and Pick-Up (Pulse) Coil Failures
If turning the ignition key produces zero neutral light, zero horn, and zero speedometer activity, pop open the side panel and check the main blade fuse (usually 10A or 15A) inside the plastic fuse holder.
If fuses and battery voltage are completely healthy on a carbureted Hero bike yet you still get zero spark when kicking, the stator pick-up coil (pulse coil) inside the left crankcase cover may have failed. That tiny sensor tells the CDI unit exactly when to fire the spark plug; when it burns out, neither kick nor self-start can create a spark.
| Electrical Symptom | Underlying Culprit | Best Action |
| Total blackout at key-on | Blown main fuse or loose battery terminal | Open side panel, inspect fuse, tighten 10mm bolts |
| Dim console on BS6, won’t kick-start | Battery below minimum ECU/pump voltage | Jump-start from another 12V battery and test RR unit |
| Good battery & crank, zero spark on carb bike | Failed pick-up (pulse) coil or CDI unit | Test pick-up coil resistance with multimeter |
Loss of Compression, Tight Valves, and Flooding Mistakes
If you have verified bright blue spark, clean fuel flow, and healthy battery voltage—yet the kick lever feels unusually soft and easy to push down—your engine lacks compression.
Tight Valve Tappets on High-Mileage Commuters
Hero’s air-cooled commuter engines regularly cross 70,000 kilometers with basic oil changes, but their intake and exhaust valve clearances slowly tighten over time.
When valve tappets lose their clearance, the valves stay slightly cracked open when the engine is cold, letting cylinder compression leak out before the fuel mixture can ignite. A classic symptom is a Hero bike that refuses to start with kick or self-start on cool mornings, yet runs fine once warmed up. Adjusting intake and exhaust tappets back to factory spec (0.05mm to 0.08mm) restores crisp compression right away.
Why Twisting the Throttle While Kicking Floods the Engine
When a stubborn engine refuses to fire, many riders instinctively twist the throttle grip repeatedly while kicking or holding the self-start button.
Twisting the throttle wide open during starting destroys intake vacuum on carbureted bikes and dumps excess raw petrol onto the spark plug. Keep your right hand completely off the throttle grip while kicking or pressing the starter—only roll the throttle open gently once the engine fires up.
| Mechanical / Technique Issue | Real-World Clue | Better Approach |
| Kick lever feels abnormally soft | Tight valve tappets or worn piston rings | Adjust valve clearances and check oil level |
| Strong petrol smell after kicking | Flooded cylinder from twisting throttle | Hold throttle wide open with key OFF, kick 5 times |
| Starts fine warm, refuses cold mornings | Tight cold valve clearance or weak choke | Check tappet gap and keep throttle closed on start |
Final Thoughts
Dealing with a Hero bike not starting with kick and self feels intimidating when both options fail at once, yet the root cause is almost always something simple shared by the whole engine. By checking whether you ride a carbureted or BS6 model first, clearing the side-stand sensor, drying the spark plug boot, checking fuel flow, and verifying battery voltage, you can diagnose the problem right on the roadside.
Keep a spare spark plug and a small plug spanner tucked inside your under-seat tool pouch, maintain at least two liters of petrol in BS6 tanks to protect the in-tank fuel pump, and keep your hand off the throttle grip while kicking. Those small everyday habits keep your Hero commuter starting reliably through rain, cold mornings, and heavy daily traffic.
Ehatasamul Alom is a dedicated road hybrid bikes expert. With over 15 years of experience, he helps people find the perfect ride. He began his journey as a bike mechanic. He learned the ins and outs of every bike.
Ehatasamul Alom holds a Master's degree in Mechanical Engineering from a Brown University (Providence US 02912), where he specialized in material science and bicycle kinematics. His master's thesis focused on optimizing frame geometry for road hybrid bikes to improve rider comfort and efficiency.
Ehatasamul has an extensive professional background. He spent 10 years (2010-2020) as a Senior Bike Designer at "Urban Cycles," a leading bicycle manufacturer. In this role, he led the development of several award-winning road hybrid bikes, which are known for their durability and performance. He later served (2020-2024) as the Head of Product Development at "Gear Up," a company specializing in high-end cycling components. There, he developed innovative parts and accessories specifically for road hybrid bikes.
Over the years, Ehatasamul has become an authority on Roadhybridbikes. He understands their design and function. His work focuses on making bikes easy to use. Ehatasamul believes everyone should enjoy cycling. He writes guides that are simple to read. His passion for road hybrid bikes is clear. His goal is to share his knowledge with everyone. He wants to see more people on two wheels. His advice is always practical and easy to follow.
